ERG550W Pre-Assembly Pack Checklist
| Part No. | Description | Quantity |
| 1 | Main Frame | 1 |
| 3 | Front Stabilizer | 1 |
| 54 | Console | 1 |
| 17 | Seat | 1 |
| 90 | Funnel | 1 |
| 4 | Front Stabilizer | 1 |
| 2 | Slide Rail | 1 |
| 83 | Pedal Plate (L) | 1 |
| 104 | Rail Endcap (R) | 1 |
| 91 | Siphon Pump | 1 |
ERG550W Step-by-Step Assembly Instructions
Note: We recommend that assembly is completed by two people to make the process easier.
1. Front Stabilizer
a. Attach the Front Stabilizer (No. 4) onto the Main Frame (No. 1) with 4 Curved Washers (No. 99) and 2 Hex Socket Round Head Screws (No. 73) and 2 Nylon Hex Nuts (No. 80).
b. Secure the Front Stabilizer (No.4) to the Main Frame (No.1) with 2 Flat Washers (No. 27), 2 Hex Socket Round Head Screws (No. 67).
c. Tighten using the Allen Wrench with Phillips Screwdriver (No. 96) provided.
2. Rear Stabilizer and Seat
a. Turn over the Slide Rail (No. 2) and Seat (No. 17) as shown.
b. Slide the Seat (No. 17) onto the Slide Rail (No. 2).
c. Secure the Limit Pad (No. 40) with 2 Hex Socket Screws (No. 65). Then attach the Rear Stabilizer (No. 3) to the Slide Rail (No. 2) with 4 Flat Washers (No. 27) and 4 Hex Bolts (No. 62).
d. Tighten with Allen Wrench with Phillips Screwdriver (No. 96) and the Open Wrench (No. 97).
3. Seat Stop
a. Attach the Stop Brackets L / R (No. 111/112) to the Sliding Rail (No. 2) and tighten the caps with 2 Self-tapping screws (No. 101).
b. Tighten using the Allen Wrench with Phillips Screwdriver (No. 96) provided.
4. Main Frame
Note: Move the seat (No. 17) to the front of the Slide Rail (No. 2) before assembly to prevent it from sliding down during assembly.
a. Attach the Slide Rail (No. 2) to the Main Frame (No. 1) using 4 Flat Washers (No. 74), 4 Hex Socket Round Hex Screws (No. 67) and 4 Hex Socket Screws (No. 66). Insert all 8 screws partially into the holes first, and then tighten using the Allen Wrench with Phillips Screwdriver (No. 96).
5. Pedals
a. Screw the Pedal Plate L (No. 83) into the Main Frame (No.1) with 2 Hex Bolts (No. 114) using the Open Wrench (No. 97). Tighten.
b. Repeat for Pedal Plate R (No. 104) to Main Frame (No. 1).
6. Console
a. Connect the wire of Console (No. 54) to the Sensor Wire Set (No. 95) from the Main Frame (No. 1).
b. Attach the Console Bracket (No. 8) which is pre-installed on the Console (No. 54) onto the Main Frame (No. 1) with 1 Hex Socket Round Head Screw (No. 51), 1 Flat Washer (No. 74) and 1 Nylon Hex Nut (No. 80).
c. Tighten using the Allen Wrench with Phillips Screwdriver (No. 96) and Open Wrench (No. 97) provided.