ERG200 Assembly Pack Checklist
| Part Number | Part Description | Quantity |
| #2 | Allen Bolt M8*75 | 2 |
| #5 | End Caps | 2 |
| #6 | Curved Washer 8*20 | 2 |
| #7 | Spring Washer 8 | 2 |
| #12 | Allen Screw M6*12 | 4 |
| #13 | Washer 6*17 | 4 |
| #15 | Axle for Pedal | 2 |
| #19 | Carriage Bolt M8*45 | 2 |
| #34 | Domed Nut M8 | 2 |
| #22 | Plastic Washer | 4 |
| #23 | Allen Screw M8*20 | 4 |
| #24 | Allen Screw M8*16 | 10 |
| #25 | Washer 8*17 | 12 |
| Box Wrench | 1 | |
| 4mm Allen Key | 2 | |
| 6mm Allen Key | 1 |
ERG200 Step-by-Step Assembly Instructions
1. Stabilizers, Console Mast, and Console
| Hardware Needed for This Step | |
| #2 | Allen Bolt (2 pcs) |
| #7 | Spring Washer (2 pcs) |
| #6 | Curved Washer (2 pcs) |
a. Attach the front stabilizer (3) to the main frame (1). Secure using two Allen bolts (#2), two curve washers (#6) and two spring washers (#7).
b. Connect the computer sensor wire (21) to the back of the computer (9). Ensure that the wires are not pinched behind the computer.
c. Attach the computer (9) to the computer bracket (62) and fasten with two pre-assembled screws (10).
2. Attaching Pedals
| Hardware Needed for This Step | |
| #19 | Carriage Bolt (2 pcs) |
| #14L | Left Pedal |
| #14R | Right Pedal |
| #15 | Axle for Pedal (2 pcs) |
| #12 | Allen Bolt (2 pcs) |
| #13 | Washer (2 pcs) |
a. Attach the left pedal (#14L) to the left bracket of pedal support tube (17). Secure using one axle for pedal (#15), two sets of Allen bolts (#12) and washers (#13).
b. Repeat the same procedure for right pedal.
c. Attach the pedal support tube (17) to the bottom of main frame (1). Secure using two sets of carriage bolts (#19), washers (#25) and domed nuts (#34).
d. Pull out the lock pin (55) from pivot on U-type connect tube (58). Flip down the bracket and insert the lock pin (55) back to the pivot to lock the bracket in horizontal position.
3. Attaching Sliding Rail Frame
| Hardware Needed for This Step | |
| #4 | Allen Bolt (10 pcs) |
| #25 | Washer (10 pcs) |
| #23 | Allen Bolt (4 pcs) |
a. Insert the sliding rail (26) to the U-type connect tube (58). Secure using four sets of Allen bolts (#24) and washers (#25) on the bottom, two sets of Allen bolts (#24) and washers (#25) on the top.
b. Attach the collar (22) to each side of the track on the end of the sliding rail (26). Secure using one Allen bolt (#23).
c. Slide the seat (11) onto the sliding rail.
d. Repeat same procedure for other two collars (22) to the other end of sliding rail (26).
e. Attach the end cap for sliding rail (5L/R) to the back of sliding rail (26).
f. Attach the rear stabilizer (28) to sliding rail (26). Secure using four sets of Allen bolts (#24) and washers (#25).