EU150 Pre-Assembly Pack Checklist
| Part Number | Part Description | Quantity |
| #6 | Curved Washer 22*10 | 4 |
| #7 | Dome Nut M10 | 4 |
| #8 | Carriage Bolt M10*75 | 4 |
| #30 | Allen Screw M8*16 | 6 |
| #31 | Curved Washer 20*8 | 6 |
| #32 | PVC Cap | 6 |
| #33 | Hex Head Screw M10*20 | 2 |
| #34 | Spring Washer 10 | 2 |
| #35 | Washer 32*10 | 2 |
| #36 | D Type Washer | 2 |
| #37 | Carriage Bolt | 4 |
| #38 | Allen Screw M6*12 | 4 |
| #39 | Hex Head Bolt M10*78 | 2 |
| #40 | Sleeve | 2 |
| #41 | Washer 10*22 | 6 |
| #42 | Nylon Nut M10 | 6 |
| #44 | Carriage Bolt M10*45 | 4 |
| #45 (Left and Right) | Hinge Bolt (L/R) | 1/1 |
| #46 | Wave Washer 16 | 2 |
| #47 | Washer 27*13 | 2 |
| #48 (Left and Right) | Lock Nut (L/R) | 1/1 |
| 4mm Allen Key | 1 | |
| 6mm Allen Key | 1 | |
| 8mm Allen Key | 1 | |
| Allen Wrench | 2 |
EU150 Step-by-Step Assembly Instructions
1. Front Stabilizer and Rear Stabilizer
| Hardware Needed for This Step | |
| #8 | Carriage Bolt (4 pcs) |
| #6 | Curved Washer (4 pcs) |
| #7 | Dome Nut (4 pcs) |
a. Attach the Front Stabilizer (2) to the front of the Main Frame (1), fasten with two Carriage Bolts (#8), two Curved Washers (#6) and two Domed Nuts (#7).
b. Repeat for the Rear Stabilizer (4) to the rear of the Main Frame (1).
2. Support Tube
| Hardware Needed for This Step | |
| #30 | Allen Screw (4 pcs) |
| #31 | Curved Washer (4 pcs) |
a. Connect the lower computer wire (58) with the upper computer wire (60). Be careful not to pinch the wires while assembling as this may cause damage to the electronics.
b. Insert the Front Post (13) into the Main Frame (1), tighten with four Allen Screws (#30) and four Curved Washers (#31).
3. Bottom Handlebars
| Hardware Needed for This Step | |
| #36 | D Type Washer (2 pcs) |
| #35 | Washer 32*10 (2 pcs) |
| #34 | Spring Washer (2 pcs) |
| #33 | Hex Head Screw (2 pcs) |
| #32 | PVC Cap (2 pcs) |
a. Attach the Left Bottom Handlebar (14) to the left side axle of the Front Post (13). Secure using one D Type Washer (36), one Washer (#35), one Spring Washer (#34) and one Hex Head Screw (#33). Attach the PVC Cap (#32) onto the Hex Head Screw (#33).
b. Repeat for the Right Bottom Handlebar (15) to the right side axle of the Front Post (13).
4. Pedal Tubes
| Hardware Needed for This Step | |
| #32 | PVC Cap (4 pcs) |
| #39 | Hex Head Bolt (2 pcs) |
| #40 | Sleeve (2 pcs) |
| #41 | Washer 10*22 (6 pcs) |
| #42 | Nylon Nut (6 pcs) |
| #44 | Carriage Bolt (4 pcs) |
| #45 | Hinge Bolt (L/R, 1/1 pcs) |
| #46 | Wave Washer (2 pcs) |
| #47 | Washer 27*13 (2 pcs) |
| #48 | Lock Nut (L/R, 1/1 pcs) |
a. Attach the Left Pedal Tube (11) to the Left Side of Crank (49). Secure using one Left Lock Nut (#48L), one Washer (#47), one Wave Washer (#46) and one Left Hinge Bolt (#45L).
b. Attach the Left Pedal Tube (11) to the Left Bottom Handlebar (14). Line up the holes and insert the Sleeve (#40) then secure using one Nylon Nut (#42), one Washer (#41) and one Hex Head Bolt (#39). Attach the PVC Cap (#32) onto both sides of the Pedal Tube (11).
c. Attach the Left Pedal (9) onto the Left Pedal Tube (11). Secure using two Carriage Bolts (#44), two Washers (#41), and two Nylon Nuts (#42).
d. Repeat the procedure for the Right Pedal Tube (12) and Right Pedal (10).
5. Handlebars and Console
| Hardware Needed for This Step | |
| #30 | Allen Screw M8*16 (2 pcs) |
| #31 | Curved Washer 20*8 (2 pcs) |
a. Attach the Stationary Handlebar (18) to the Front Post (13). Secure using two Allen Screws (#30) and two Curved Washers (#31).
b. Insert the Hand Pulse Wires (63) through the Grommet (61) on the Front Post (13), and then pull it out from the top of the Front Post (13). Connect the Sensor Wire and Hand Pulse Wire (63) with the Computer (19) accordingly.
c. Attach the Computer (19) to the Front Post (13) and fasten with four pre-assembled Screws (#62).
d. Attach the Seat (22) onto the Seat Post (20), line up the holes then tighten with one pre-assembled Carriage Bolt (#26), one pre-assembled Quadrate Plate (#27), one pre-assembled Sleeve (28), and one pre-assembled Lock Knob (#29).
e. Unscrew the Quick Release Knob (57) from the Main Frame (1), insert the Seat Post (20) into the Main Frame (1). Line up the holes and secure seat in position with Quick Release Knob (57). The correct height for seat can be adjusted after the upright elliptical is fully assembled.
6. Handlebars
| Hardware Needed for This Step | |
| #38 | Allen Screw M6*12 (4 pcs) |
| #37 | Carriage Bolt (4 pcs) |
a. Connect the Left Top Handlebar (16) to the Left Bottom Handlebar (14). Secure using two Allen Screws (#38) and two Carriage Bolts (#37).
b. Repeat for the Right Top Handlebar (64) to the Right Bottom Handlebar (15).