Pre-Assembly
SB4500 Assembly Pack Checklist
Assembly
SB4500 Step-by-Step Assembly Instructions
1. Front Stabilizer
Hardware Needed for This Step | |
#57 | M8 x 50mm Carriage Bolt (2 pcs) |
#58 | 8 x 16 x 1.5T Flat Washer (2 pcs) |
#59 | M8 Cap Nut (2 pcs) |
a. Install the Front Stabilizer Tube (No. 11) onto the Main Frame and secure using two Carriage Bolts (No. 57), two Flat Washers (No. 58), and two Cap Nuts (No. 59).
2. Rear Stabilizer
Hardware Needed for This Step | |
#57 | M8 x 50mm Carriage Bolt (2 pcs) |
#58 | 8 x 16 x 1.5T Flat Washer (2 pcs) |
#59 | M8 Cap Nut (2 pcs) |
a. Install the Rear Stabilizer Tube (No. 12) onto the Main Frame and secure using two Carriage Bolts (No. 57), two Flat Washers (No. 58), and two Cap Nuts (No. 59).
3. Connecting the Main Frame
Hardware Needed for This Step | |
#55 | 8 x 21 x 2T Flat Washer (6 pcs) |
#36 | M8 x 15mm Phillips Head Screw (6 pcs) |
a. Connect the two Handpulse Wires (No. 79 & 80) together. Be careful not to pinch the wires and feed them back into the connected frame.
b. Assemble the Front Main Frame (No.1) to the Rear Main Frame (No. 2) using six Flat Washers (No. 55).
c. Secure on top with six Phillips Head Screws (No.36).
4. Console Mast
Hardware Needed for This Step | |
#55 | 8 x 21 x 2T Flat Washer (4 pcs) |
#39 | M5 x 15mm Phillips Head Screw (2 pcs) |
#54 | Cup Washer M8 (1 pcs) |
#36 | M8 x 15mm Phillips Head Screw (6 pcs) |
a. Run the two Cables (No. 74 & 78) through the Console Mast (No. 3). Connect the two Computer Cables (No. 74 & 75) and two Handpulse Wires (No. 78 & 79) together.
b. Secure the Console Mast (No. 3) to the Main Frame using six Phillips Head Screws (No.36), four Flat Washers (No. 55), and one Cup Washer (No. 54).
c. Secure the Drink Bottle Holder (No. 68) to the Console Mast (No.3) using two Phillips Head Screws (No. 39).
5. Front Handlebars
Hardware Needed for This Step | |
#36 | M8 x 15 Phillips Head Screw (4 pcs) |
a. Secure the Mast Handle Bar – L (No.4) and the Mast Handle Bar – R (No.5) using four Phillips Head Screws (No.36).
6. Console
Hardware Needed for This Step | |
#39 | M5 x 15 Phillips Head Screw (4 pcs) |
a. Connect the Computer Cable (No. 74) with the Handpulse Wire (No. 78). Feed the excess wire into the tube. Be careful not to pinch the wires.
b. Secure the Console (No. 70) to the Mast using four Phillips Head Screws (No. 39).
7. Seat Back Bracket
Hardware Needed for This Step | |
#52 | M8 x 40 Button Head Socket Screw (4 pcs) |
a. Secure the Seat Back Bracket (No. 9) to the Sliding Seat Plate using four Button Head Socket Screws (No. 52). Connect the two Handpulse Wires (No. 83 & 80).
8. Lower Seat Cushion
Hardware Needed for This Step | |
#36 | M8 x 15 Phillips Head Screw (4 pcs) |
a. Secure the Seat Cushion (No. 67) to the Seat Back Bracket (No. 9) using four Phillips Head Screws (No. 36).
9. Seat Handlebars
Hardware Needed for This Step | |
#36 | M8 x 15 Phillips Head Screw (4 pcs) |
a. Connect the Handpulse Wires (No. 81 & 83).
b. Secure the Seat Handle Bar – L (No. 6) and the Seat Handle Bar – R (No. 7) using four Phillips Head Screws (No. 36).
10. Upper Seat Cushion
Hardware Needed for This Step | |
#36 | M8 x 15 Phillips Head Screw (4 pcs) |
a. Secure the Seatback Cushion (No. 66) to the Seat Back Bracket (No. 9) using four Philips Head Screws (No. 36).
11. Pedals
a. Secure the Pedal - L (No. 64) and Pedal - R (No. 65) using the Phillips Head Screwdriver & Wrench (No. 61). The Left Pedal (No. 64) should be tightened counter-clockwise and the Right Pedal (No. 65) clockwise.
b. Secure all screws and adjust the five levelers to sit evenly on your floor.