Pre-Assembly
SB150 Assembly Pack Checklist
| Part No. | Part Description | Quantity |
| #2 | Allen Screw M8*75 | 2 |
| #4 | Spring Washer | 2 |
| #5 | Curved Washer 8*20*1.5 | 12 |
| #21 | Allen Screw M8*16 | 30 |
| #23 | Carriage Bolt M10*75 | 2 |
| #24 | Curved Washer 10*22*1.5 | 2 |
| #28 | Carriage Bolt M8*40 | 2 |
| #29 | Domed Nut M8 | 2 |
| #31 | Domed Nut M10 | 2 |
| #38 | Flat Washer 17*8.5 | 6 |
| #39 | Leveling Pad | 1 |
| #42 | Quick Release Knob | 1 |
| #88 | Box Wrench | 1 |
| #89 | Allen Key 6mm | 1 |
Assembly
SB250 Step-by-Step Assembly Instructions
1. Front Stabilizer
| Hardware Needed for This Step | |
| #2 | Allen Screw (2 pcs) |
| #5 | Curved Washer (2 pcs) |
| #4 | Spring Washer (2 pcs) |
a. Attach the front stabilizer (3) to the main frame (1), securing with two Allen screws (#2), two spring washers (#4) and two curved washers (#5).
2. Support Tube and Rear Stabilizer
| Hardware Needed for This Step | |
| #21 | Allen Screw (6 pcs) |
| #38 | Flat Washer (6 pcs) |
| #23 | Carriage Bolt (2 pcs) |
| #24 | Curved Washer (2 pcs) |
| #31 | Domed Nut (2 pcs) |
a. Connect middle extension hand pulse wire (33) with rear extension hand pulse wire (34). Attach support tube (40) to main frame (1), and tighten with 6 sets of Allen screw (#21) and flat washer (#38). Attach the leveling pad (39) to the bottom of main frame (1).
b. Attach rear stabilizer (6) to the support tube (40) and tighten with 2 sets of carriage bolt (#23), curved washer (#24) and domed nut (#31). Tip: avoid pinching the extension wires.
3. Console and Upright
| Hardware Needed for This Step | |
| #5 | Curved Washer (8 pcs) |
| #21 | Allen Screw (8 pcs) |
a. Connect the upper extension computer wire (19) to the lower computer wire (32).
b. Connect the front extension hand pulse wire (18) to the middle extension hand pulse wire (33).
c. Attach front post (9) to the main frame. Secure using four curved washers (#5) and four Allen screws (#21). Tip: avoid pinching the extension wires and hand pulse wires.
d. Attach the left stationary handlebar (12) to the front post (9). Secure using two curved washers (#5) and two Allen screws (#21). Repeat for the right stationary handlebar (11).
e. Connect the front extension hand pulse wire (18) to the pulse wire from the computer (10).
f. Connect the upper extension computer wire (19) to the wire from the computer (10). Tip: avoid pinching the extension wires and pulse wires.
g. Attach the computer (10) to the top bracket of front post (9). Secure using four screws (20) which are pre-assembled on the back of computer.
h. Attach bottle holder (46) to the front post (9). Secure using two screws (54) which are pre-assembled on the front post (9).
4. Seat Assembly
| Hardware Needed for This Step | |
| #21 | Allen Screw (12 pcs) |
a. Insert the sliding tube (41) into seat support bracket (43). Line up the holes and secure sliding tube (41) with quick release knob (42).
b. Attach seat cushion (45) to the seat support bracket (43). Secure using four Allen screws (#21).
c. Attach the sliding tube (41) to the support tube (40). Secure using eight Allen screws (#21).
5. Rear Handlebar Assembly
| Hardware Needed for This Step | |
| #21 | Allen Screw (4 pcs) |
| #28 | Carriage Bolt (2 pcs) |
| #5 | Curved Washer (2 pcs) |
| #29 | Domed Nut (2 pcs) |
a. Attach back cushion (44) to the seat support bracket (43). Secure using four Allen screws (#21).
b. Attach rear handlebar (13) to the seat support bracket (43). Secure using two carriage bolts (#28), two curved washers (#5) and two domed nuts (#29).
c. Connect rear extension hand pulse wire (34) to the hand pulse wire (35). Tip: avoid pinching the pulse wires.
6. Pedals and Base Cover
a. The left and right pedals (37 & 36) are marked “L” & “R”. Attach the straps to the pedals. Connect the right pedal (36) to the crank (17) on the right hand side of the cycle as you sit on it. Repeat for the left pedal (37). Note: the right pedal should be threaded on clockwise and the left pedal on counter-clockwise.
b. Attach the left rear support cover (47) to the left side of the support tube (40). Secure using two self tapping screws (53).
c. Attach the right rear support cover (48) to the right side of the support tube (40). Secure using three self tapping screws (53).
7. Power Adapter and MP3
To listen to an MP3 during your workout, connect the MP3 with the computer (10) by using the audio wire (87). Plug adapter into the power receptacle.
